Dentsply SDR Flowable Posterior Bulk Filling Material FREE SHIPPING WORLDWIDE

Description: DESCRIPTION SDR Posterior Bulk Fill Flowable Base is a one-component, fluoride-containing, visible light cured, radiopaque resin composite restorative material. It is designed to be used as a base in class I and II restorations. SDR™ material has handling characteristics typical of a “flowable” composite, but can be placed in 4 mm increments with minimal polymerization stress. SDR™ material has a self-leveling feature that allows intimate adaptation to the prepared cavity walls. Available in one universal shade, it is designed to be overlayed with a methacrylate based universal/posterior composite for replacing missing occlusal/facial enamel. COMPOSITIONBarium-alumino-fluoro-borosilicate glassStrontium alumino-fluoro-silicate glassModified urethane dimethacrylate resinEthoxylated Bisphenol A dimethacrylate (EBPADMA)Triethyleneglycol dimethacrylate (TEGDMA)Camphorquinone (CQ) PhotoinitiatorButylated hydroxytoluene (BHT)UV StabilizerTitanium dioxideIron oxide pigments INDICATIONS SDR material direct restorative:Base in cavity class I & II direct restorationsLiner under direct restorative materials – Class II box linerContraindications SDR™ material is contraindicated for: • Use with patients who have a history of severe allergic reaction to methacrylate resins. Advantages Advanced Chemistry and amazing ProceduresBulk Fill base in Class I and II restorations 4mm depth of cure Self Leveling Handling Up to 60% less stress than conventional flowable RadiopaqueSingle component, fluoride containing, visible light cured Note: Images are for illustration only. Company may change item design / pattern /packaging from time to time. We will ship only the latest packing available at time of shipping. Direction to use Cavity PreparationPrepare the cavity so that no residual amalgam or restorative material is leftRinse the surface with water spray and carefully dry it with air spray. Do not desiccate the tooth structureUse a dental dam or cotton rolls to isolate the cavity from contamination. Placement of Matrix For optimal proximal contacts proceed as follows:Place a matrix (e.g. AutoMatrix® matrix system or Palodent matrix system) and wedge. Burnishing of the matrix band will improve contact and contour. Pre-wedging/BiTine® ring placement is advocatedIn class II cavities use a deadsoft, thin matrix band. Pulp protection, Tooth Conditioning/Dentin Pretreatment, Adhesive Application Refer to adhesive manufacturer’s directions for pulp protection, tooth conditioning and/or adhesive application. Once the surfaces have been properly treated, they must be kept uncontaminated. Proceed immediately to placement of SDR material. Dispensing SDR material The pre-dosed Compula® Tip provides the combination of a unit dose Compules® Tip with a metal cannula applicator TipLoad Compules® Tips Gun with pre-dosed Compula Tip. Insert Compula® Tip into the notched opening of the Compules® Tips Gun barrel. Be certain that the collar on the Compula® Tip is inserted first. 5 2. Remove the colored cap from the Compula® Tip. The Compula® Tip may be rotated 360° to gain the proper angle of entrance into the cavityDispense the material into the cavity preparation using a slow, steady pressure. DO NOT USE EXCESSIVE FORCE.To remove the used Compula Tip, be sure that the Compules Tips Gun plunger is pulled back completely by allowing the handle to open to its widest position. Apply a downward motion to the front end of the Compula Tip and remove. Placement of SDR material Note: As SDR™ material is designed to conform to cavity shape, proper contact areas must be established with the matrix system selected. Material will not distend matrix band. If needed, manually distend matrix band with a suitable hand instrument such as a condenser or ball burnisher prior to and/or during light curingDispense SDR™ material directly into the preparation site/tooth surface from the Compula Tip using slow, steady pressure. Begin dispensing at the deepest portion of the cavity, keeping Tip close to the cavity floor. Gradually withdraw Tip as the cavity is filled. Avoid lifting the Tip out of dispensed material while dispensing to minimize air entrapment. At the completion of dispensing, wipe Tip against cavity wall while withdrawing from the operative fieldWithin a few seconds, dispensed SDR material will self-level, eliminating the need for further manipulation with hand instruments. In case of overfill or excess on occlusal margins, use a flocked applicator Tip wetted with residual adhesive to remove excess. Any visible air bubbles should be pierced with a clean, sharp explorer prior to curingWhen used as a Bulk Fill Base material, most cavities may be filled in one bulk increment up to 4 mm as needed to fill the cavity 2 mm short of the occlusal cavosurface. In deeper preparations, place material in 4 mm increments, thoroughly light curing each incrementAlternatively, SDR™ material may be placed in a thin layer as a traditional “flowable” liner on exposed dentin. Curing SDR material is designed to be cured in increments up to a 4 mm depth/thicknessLight cure each area of the restoration surface with a suitable visible light curing unit designed to cure materials containing camphorquinone (CQ) initiator, i.e. spectral output containing 470 nm. Minimum light output must be at least 550 mW/cm2 exposure for at least 20 seconds. Refer to curing light manufacturer’s recommendations for compatibility and curing recommendations.CompletionProceed immediately to complete the restoration using a methacrylate based universal/posterior restorative material following manufacturer’sDirections For Use. Technique Tip: In most applications, a body shade of occlusal restorative material provides the best esthetic result. In case of heavily stained dentin, use of an opaque shade may be required. Do not disturb or allow contamination of cured surface or exposed adhesive. If contamination occurs, follow adhesive manufacturer’s directions for use for re-application of adhesive. If surfaces remain undisturbed, additional application of adhesive between increments is neither necessary nor recommended.If contouring, finishing, and/or polishing of cured SDR™ material is necessary, use traditional rotary devices following manufacturer’s Directions For Use. PAYMENT POLICY Payment should be cleared within 3 (three) days of sale and we prefer PayPal payment method only. WORLDWIDE SHIPPING POLICY Item will be send by ordinary registered airmail service (India Post) which may take 10 to 15 days but we assume maximum 28 business days for deliver it . You will have to sing on delivery at the time of receiving item We also provide speed post shipping service (EMS). For this service you need to pay shipping charges. As per the item weight and country location. RETURN POLICY In case of any problems after receiving the item. Please contact within 7 days and only the purchase amount will be refunded not the postage amount. One side postage for returning the item will be paid by the buyer. Money will be refunded by PayPal after the item is received. CUSTOM POLICY Import duties, taxes and charges are not included in the item price or the shipping charges. These charges are the buyer's responsibility. Please check with your local customs authority to determine these additional costs prior to bidding or buying. DISCLAIMER The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, do not bid on this item unless you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item. (FeedBack) Your *feedback is important for us to grow our business on eBay, so please do leave feedback. CONTACT US For Any query, we request you to either use the ask question button. we normally reply back the same day or the next working day. We are available 24*7.We reply back to emails within 12-24 Hours.

Price: 92.98 USD

Location: DELHI, DELHI

End Time: 2024-11-07T17:53:41.000Z

Shipping Cost: 0 USD